4 volts simple inverter project: explanation

← Previous Page
Next Page →

4 volts simple inverter: In mini electronic projects, conversion of DC voltage to AC voltage is a very interesting and common problem. In most circuits, we observe that almost all design of the circuit takes the AC input and gives DC output. But, as we want to change the circuit from DC to AC then a DC to AC converter circuit is used. The converter/inverter is required for this purpose. So, to convert the DC to AC converter circuit is used.

In this mini electronics project, I am going to make a very simple but very very interesting circuit. This circuit is 4 volts DC to 220 volts AC.  I have used very simple and scraped components to build this circuit. These components are found in mobile chargers and also in CFL circuits.

4 volts simple inverter circuit diagram

4 volts simple inverter project: explanation

Components Required 4 volts simple inverter

  • Transformer from old mobile charger circuit
  • 10 to a 110-ohm resistor
  • 13005 or equivalent Transistor
  • 4.5uf capacitor from old CFL circuit
  • 4 volts batteries
  • some Pieces of Wires

MJE 13005 Transistor Points

MJE 13005 Transistor Points

Transformer ( From mobile phone charger or equivalent)

In this circuit, we can use a mobile phone charger transformer. Keep in mind all mobile phone charger circuit has different structure for the transformer. So you must check the transformer structure before using it in this mini 4 to 220v inverter.

Transformer ( From mobile phone charger or equivalent)

Measurement of This type of transformer

you can measure this transformer by using a multimeter. We must have to use the maximum ohm coil of the transformer for output.

Measurement of This type of transformer you can measure this transformer by using a multimeter. We must have to use the maximum ohm coil of the transformer for output.

If Does not Work through this connection then just make a little change. Resistor connection replaces with point no 6 to point no 5. The jumper of + changes from point no 5 to 6. The circuit diagram is given below.

Alternate Circuit Diagram for 4v inverter

If the above circuit does not work then change the connections like the given below circuit diagram it will work 100 percent. It is a very simple 4 volts simple inverter which is why its power is very low so uses minimum watts as output to get the result.

Alternate Circuit Diagram for 4v inverter

Note: Because it is a developed transformer for the mobile charger so it is a very low-power transformer. You can make your own transformer for better results with this inverter.  because it’s very short with few components power inverter that is a transistor may heat. So use a heat sink with a transistor.

For Full Detail Project Watch This Video

DC to AC Power Converter circuit feature working

DC to AC Power Converter is often needed at the places where it is not possible to get AC supply. DC to AC power converter circuit is used to convert the DC power to AC power. In this article, we are going to make 1.5v DC to 220v AC. Converters can be of two types pure sine wave converters and quasi or modified converters. Pure sine wave converters are costly but modified or quasi-converters are inexpensive. These modified dc to ac power Converter produces a square wave and these are not used to power delicate electronic equipment.  I am explaining a modified DC-to-AC converter is a very simple way with only 1 transistor and Two transistors.

Dc to ac power converter with a single transistor

In the first circuit diagram, we have built a very very simple dc to ac converter with a single transistor only. It’s not a Pure sine wave inverter so please do not check its output with a multimeter because your multimeter will be damaged if you check the output with it.

DC to AC Power Converter circuit feature working

Components required for DC to AC inverter

  1. 12v Battery
  2. 2sc5200 Transistors
  3. 220ohm to 1k Resistor (depending on your transformer)
  4. 12-0-12   220 Volts step-up transformer. (6-0-6 transformer will also work)

A 12 Volts DC to AC converter can also be designed using MOS FITS.

 

12 Volts DC to AC converter

Principle Of this Circuit

The basic idea behind every dc to ac converter circuit is to produce oscillations using the given DC and apply these oscillations across the primary of the transformer by amplifying the current. This primary voltage is then stepped up to a higher voltage depending on the number of turns in primary and secondary coils. keep in mind if the turns of coils will be more then the converter will produce high volts and if the number of turns will be few then it will generate low voltages.

Components required

  1. 12v Battery
  2. 2sc5200 Transistors
  3. 1 to 5k Resistor (depending on your transformer)
  4. 12-0-12   220 Volts step-up transformer.

You can also design DC to  AC converter with a misfit.

Two Transistor  simple DC to AC Power Converter with 2sc5200 NPN (transistor)

DC to AC Power Converter circuit feature working

Animated circuit diagram DC to AC Power Converter

DC to AC Power Converter circuit feature working

It is also the same as a single dc to ac converter transistor invert-er only difference is that it has two transistors 12v inverters. Its power is two times better than a single transistor dc to the ac power inverter transistors which we have used are also very powerful so these transistors can not heat up while working.

working is the same as a single transistor you may use a 6-0-6 transformer with 6-volt DC. It’s an experimental invert-er. you can use a PNP transistor instead of NPN only ischemic will be changing here we are also uploading the circuit diagram with a PNP transistor.

Circuit Diagram with PNP transistor

Circuit Diagram with PNP transistor

It is a circuit diagram for the PNP transistor. In any case of any problem please freely ask anything about circuits in the comments box we will reply to you as soon as possible.

1.5v volts DC to AC Power Converter

 

Related posts
← Previous Page
Next Page →